Umhlahlandlela ophelele wemiyalo ye-MITTUBUBISHI PLC: Master lonke uchungechunge endaweni eyodwa

Umhlahlandlela ophelele wemiyalo ye-MITTUBUBISHI PLC: Master lonke uchungechunge endaweni eyodwa

Ensimini yezimboni ezenzakalelayo, ama-mitsubishi PLCs (abalawuli abahlelekile abahlelekile) bamukelwe kabanzi ngokusebenza kwabo ngamandla kanye nokwethenjwa okuphezulu. Le ndatshana ihlinzeka ngokuqhekeka okuningiliziwe kwemiyalo esemqoka Mitsubishi PLC, kufaka phakathi:

• Imiyalo nemiyalo yokukhipha

• Uchungechunge lokuxhumana nemiyalo yokuxhumana ehambisanayo

• Vimba imiyalo yokusebenza

• Setha futhi usethe kabusha imiyalo

• Imiyalo ehlukile yokuhlukanisa

• Imiyalo Yokulawula Kakhulu

• Imiyalo ye-Stack

• I-Invert / Ayikho Imiyalo Yokusebenza / End

• Imiyalo yesitebhisi yesinyathelo

Inika amandla amandla okusebenza okuphelele kohlelo lwe-MITSISUBISHI PLC.

I. Ukulayisha nokukhipha Imiyalo

• I-LD (ukufundiswa komthwalo): Ixhumanisa oxhumene naye ovulekile (cha) othintana naye osezingeni lesitimela. Okuphoqelekile ngemigqa ye-logic kuqala ngoxhumana naye.

• I-LDI (Layisha Imiyalo Engagxiliwe): Ixhumanisa ukuxhumana okujwayelekile okuvaliwe (NC) kujantshi wesobunxele. Okuphoqelekile ngemigqa ye-logic kuqala ngoxhumana naye we-NC.

• I-LDP (Layisha Ukukhuphuka Okumilolonga)

• I-LDF (Layisha Ukuwa Kwemibhalo Enqenqemeni)

• Out (Ukukhishwa kokukhipha): Kushayela ikhoyili (into yokuphuma).

Amanothi Wokusetshenziswa:

• I-LD / LDI ingaxhuma kujantshi wesobunxele noma uhlanganise ne-ANB / ORB yokuvimbela ukusebenza kwemininingwane.

• I-LDP / LDF igcina i-activation yomjikelezo owodwa we-scan kuphela ekutholweni komngcele ovumayo.

• Izinto eziqondisiwe ze-LD / LDI / LDP / LDF: x, y, m, t, c, s.

• Ngaphandle kungasetshenziswa ngokulandelana (okulingana namakhoyili afanayo). Okwama-timers (t) kanye nama-counter (c), chaza njalo k noma irejista yedatha ngemuva kokuphuma.

• Izinto eziqondisiwe zodwa: y, m, t, c, s (hhayi x).

II. Imiyalo Yokuxhumeka Kochungechunge

• Futhi: Uchungechunge-luxhuma ukuthi ungaxhumana (unengqondo futhi).

• I-ANI (ne-Inverser): Uchungechunge-luxhumanisa ukuxhumana kwe-NC (okunengqondo futhi - hhayi).

• I-AndP: Ukuxhumeka kochungechungechungechunge lokuthola uchungechunge lokuthola usizo.

• I-Andf: Ukuhlangenwelwa kochungechungechungechunge lwe-Falling-Edget-Edge detection Section.

Amanothi Wokusetshenziswa:

• Kanye / ne-ANI / andP / andF ukweseka ukuxhumeka kochungechunge olungenamkhawulo olungenamkhawulo.

• Izinto eziqondisiwe: x, y, m, t, c, s.

• Isibonelo: ukuphuma kwe-M101 kulandelwa kanye ne-T1 Driving Y4 kuyinto "okuphumayo."

III. Thintana nemiyalo yokuxhumana ehambisanayo

• Noma: ukufana - kuxhuma othintana naye (onengqondo noma).

• Ori (noma ukuphambuka): I-Parallel-ixhumanisa ukuxhumana kwe-NC (okunengqondo noma - hhayi).

• I-ORP: Ukutholwa okuphezulu kokutholwa okufanayo.

• I-ORF: Ukuwa kokutholwa komngcele okufana nokuthola okufanayo.

Amanothi Wokusetshenziswa:

• Iziphetho zesobunxele Xhuma ku-LD / LDI / LDP / LPF; I-Right igcina isixhumanisi sokuphela komyalo wangaphambilini. Ukusetshenziswa okungenamkhawulo okuhambisana nakho.

• Izinto eziqondisiwe: x, y, m, t, c, s.

IV. Vimba imiyalo yokusebenza

• I-Orb (noma ibhlokhi): Ukuxhumeka okuhambisanayo kwemibuthano yokuxhumana emibili noma ngaphezulu.

• I-ANB (neBlock): Ukuxhumeka kwamasekethe okuxhumana okubili noma ngaphezulu okufanayo.

Amanothi Wokusetshenziswa:

• I-Conch Circuit Block ngayinye ku-Orb kumele iqale nge-LD / LDI.

• I-block ngayinye yesifunda elihambisanayo ku-ANB kumele iqale nge-LD / LDI.

• Umkhawulo wemiyalo engu-8 elandelanayo ye-ORB / ANB.

V. Setha futhi usethe kabusha imiyalo

• Setha: Kusebenze futhi kuthambe i-Target element.

• I-RST: Yenza isebenze futhi isula into eqondiwe.

Amanothi Wokusetshenziswa:

• Setha okuhlosiwe: y, m, s.

• I-RTS TALTS: y, m, s, c, d, v, z. Clula amarejista wedatha (D, z, v) bese usetha kabusha timers / counters.

• LaIsethi / i-ST esetshenzisiwe yento enikeziwe iqala ukwedlula.

VI. Imiyalo ehlukile yokuhlukanisa

• I-Pls (Pulse Rising Edge): Ikhiqiza i-Scan-Cycle Pulse off → Kuguquko.

• I-Plf (Pulse Falling Edge): Ikhiqiza i-scan-cycle eyodwa ye-pulse on → Off Transition.

Amanothi Wokusetshenziswa:

• Imigomo: y, M.

• Pls: Iyasebenza ngomjikelezo owodwa wokuskena ngemuva kokuvulwa kokushayela.

• I-PLF: Iyasebenza ngomjikelezo owodwa wokuskena ngemuva kokuvalwa kokushayela.

VII. Imiyalo Yokulawula Kakhulu

• I-MC (Master Control): Ixhuma Oxhumana Nabo Othile Othile. Ishintsha isikhundla sesobunxele sesobunxele.

• I-MCR (Ukulawula Ukulawula Kakhulu): Ukusetha kabusha i-MC, Ukubuyisela Isitimela Soqobo Kwesobunxele.

Amanothi Wokusetshenziswa:

• Okuhlosiwe: y, m (hhayi ukudluliselwa okukhethekile).

• I-MC idinga izinyathelo zohlelo ezi-3; I-MCR idinga 2.

• Ukuxhumana kwe-Master Control kungukuthintwa okuxhunyiwe kuxhumeke kujantshi wesobunxele. Oxhumana nabo ngezansi kumele baqale nge-LD / LDI.

• Lapho okokufaka kwe-MC kuvaliwe: Ama-Timers afakiwe / izinto zokubala nezinto ezisethiwe / ze-RST-eziqhutshwayo zigcina isimo; Izikhathi ezingafakwanga ama-litched / amabala nokusetha kabusha okuphuma ngaphandle.

• Isekela isidleke seleveli esingu-8 (N0-N7). Setha kabusha nge-MCR ngokuhleleka kabusha.

VIII. Imiyalo ye-Stack

• I-MPS (Push Stack): Izitolo ezisebenza zingumphumela wokufaka phezulu.

• I-MRW (funda isitaki): Ifunda inani eliphezulu ngaphandle kokususwa.

• I-MPP (POP Stack): Ifunda inani eliphezulu bese lilisusa.

Amanothi Wokusetshenziswa:

• Izinto eziqondiwe: Akukho (isitaki kuphela).

• Ama-MPS ne-MPP kumele abhangqwe.

• Ukujula kwesitaki okuphezulu: amazinga ayi-11.

Ix. Phendukela, akukho zifundo zokusebenza & ukuphela

• I-VING (NEVERT): Ukungena emkhunjini owedlule we-logic. Ayikwazi ukuxhuma ku-Power Rail noma i-Standalone.

• Nop (akukho ukusebenza): imiyalo engenalutho (ihlala isinyathelo esisodwa). Isetshenziselwa ukususwa kwesikhashana.

• Ukuphela (ukuphela): kuqeda ukubulawa kohlelo. Yehlisa isikhathi sokujikeleza komjikelezo.

Amanothi Wokusetshenziswa:

• Sebenzisa ukuphela ngesikhathi sokuhubhula ukuhlukanisa izigaba zohlelo.

X. Isitebhisi se-Step Ladder

• I-STL (Oxhumana Nayo Isitebhisi): Ukwenza kusebenze Isinyathelo Sokulawulwa kwesimo se-State Relay s (E.G., STL S200).

• I-RET (Buyisela): Iphuma ileli lesinyathelo bese libuyela ohlelweni oluphambili.

Umdwebo we-State Transion:

• Izinqubo ezilandelanayo zihlukaniswa ezifundeni (izinyathelo), ngamunye enza isenzo esiyingqayizivele.

• Ukuguqulwa kwenzeka lapho izimo (e.g., X1 = ku) ziyahlangabezana.

• Umbuso ngamunye uchaza:

• Izenzo eziphumayo

• Isimo Sokuguqula

• I-Next-State Target (E.G., S20 → S21).